GIT – is an acronym for Virtual Local Area Network. Several VLANs can co-exist on a single physical switch, which are configured via software ( commands and configuration files) and not through hardware interface (you still need to configure switch).

Hubs or switch connects all nodes in a LAN and node can communicate without a router. For example, all nodes in LAN A can communicate with each other without the need for a router. If a node from LAN A wants to communicate with LAN B node, you need to use a router. Therefore, each LAN (A, B, C and so on) are separated using a router.

VLAN as a name suggest combine multiple LANs at once. But what are the advantages of VLAN?

  • Performance
  • Ease of management
  • Security
  • Trunks
  • You don’t have to configure any hardware device, when physically moving server computer to another location etc.

VLAN concepts and fundamental discussion is beyond the scope of this article. I am reading following textbooks. I found these textbooks extremely useful and highly recommended:

  • Cisco CNNA ICND books (part I and II)
  • Andrew S. Tanenbaum, Computer Networks book

Linux VLAN Configuration Issue

I am lucky enough to get couple of hints from our internal wiki docs .

  • Not all network drivers support VLAN. You may need to patch your driver.
  • MTU may be another problem. It works by tagging each frame i.e. an Ethernet header extension that enlarges the header from 14 to 18 bytes. The VLAN tag contains the VLAN ID and priority. See Linux VLAN site  for patches and other information.
  • Do not use VLAN ID 1 as it may be used for admin purpose.

Linux VLAN How To

My VLAN ID is 5. So I need to copy file /etc/sysconfig/network-scripts/ifcfg-eth0 to /etc/sysconfig/network-scripts/ifcfg-eth0.5

# cp /etc/sysconfig/network-scripts/ifcfg-eth0 /etc/sysconfig/network-scripts/ifcfg-eth0.5
Now, I’ve one network card (eth0) and it needs to use tagged network traffic for VLAN ID 5.

  • eth0 – Your regular network interface
  • eth0.5 – Your virtual interface that use untagged frames

Do not modify /etc/sysconfig/network-scripts/ifcfg-eth0 file. Now open file /etc/sysconfig/network-scripts/ifcfg-eth0.5 using vi text editor:
# vi /etc/sysconfig/network-scripts/ifcfg-eth0.5
Find DEVICE=ifcfg-eth0line and replace with:
Append line:
Also make sure you assign correct IP address using DHCP or static IP. Save the file. Remove gateway entry from all other network config files. Only add gateway to /etc/sysconfig/network file. Save and close the file. Restart network:
# /etc/init.d/network restart
Please note that if you need to configure for VLAN ID 2 then copy the copy file /etc/sysconfig/network-scripts/ifcfg-eth0 to /etc/sysconfig/network-scripts/ifcfg-eth0.2 and do the above procedure again.

Using vconfig

Above method is perfect and works with Red hat Enterprise Linux / / Fedora Linux without any problem. However, you will notice that there is a command called vconfig. The vconfig program allows you to create and remove vlan-devices on a vlan enabled kernel. Vlan-devices are virtual ethernet devices which represents the virtual lans on the physical lan.

Please note that this is yet another method of configuring VLAN. If you are happy with above method no need to read below.

Add VLAN ID 5 with follwing command for eth0:
# vconfig add eth0 5

The vconfig add command creates a vlan-device on eth0 which result into eth0.5 interface. You can use normal ifconfig command to see device information:
# ifconfig eth0.5
Use ifconfig to assign IP address to vlan interfere :
# ifconfig eth0.5 netmask broadcast up
Get detailed information about VLAN interface:
# cat /proc/net/vlan/eth0.5
If you wish to delete VLAN interface delete command:
# ifconfig eth0.5 down
# vconfig rem eth0.5

Print Friendly, PDF & Email



Bài viết liên quan